ASTM A593 PDF

we manufacture one of the widest ranges of ASTM A Fasteners. Exporter of a wide range of ASTM A Fasteners in India at Best Factory lized. or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. This specification for ASTM F covers the requirements for stainless steel bolts , hex cap screws, and studs to in., inclusive, in nominal diameter in a.

Author: Nejinn Taut
Country: Netherlands
Language: English (Spanish)
Genre: Business
Published (Last): 19 December 2004
Pages: 40
PDF File Size: 12.22 Mb
ePub File Size: 18.37 Mb
ISBN: 890-6-59331-543-6
Downloads: 50956
Price: Free* [*Free Regsitration Required]
Uploader: Kizil

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age 5a93 after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

Please find below chemical, mechanical, supply condition, heat treatment, marking and other requirements on Stainless Steel Bolts.

ASTM F Specification – Boltport Fasteners LLP

This specification covers the requirements for stainless steel bolts, hex cap screws, and stud bolts in imperial size 0. Hex head, square head and hex socket cap screws. Option A tests should be made whenever feasible.

SH – Machined from strain hardened stock or cold worked to develop the specific properties.

ASTM F – Portland Bolt

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

D Yield strength is the stress at which an offset of 0.

TOP Related Articles  GRC300 DOWNLOAD

A Tensile stress areas are computed using the following formula: Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts. B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc. CW – Ashm and rolled from annealed stock thus acquiring a degree of cold work. A Minimum values except where shown as maximum or as a range.

A – Machined from a5933 or solution annealed stock thus aa593 the properties of the original material; or hot formed and solution annealed. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. B legend of conditions: D Yield strength is the stress at which an offset of 0.

B legend of conditions: Option A a539 should be made whenever feasible. F When approved by the purchaser, alloys or Se may be furnished.

A Tensile stress areas are computed using the following formula: A Minimum values except where shown as maximum or as a range. D When approved by the purchaser, alloysSe, or XM1 may be furnished. SH – Machined from strain hardened stock or cold worked to develop the specific properties.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled zstm annealed stock thus acquiring a degree of cold work.

E When approved by the purchaser, alloy 5a93 may be furnished. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F F When approved by the purchaser, alloys or Se may be furnished. A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed.

TOP Related Articles  BENEDIKTIONALE DOWNLOAD

A Where options are given, all the tests under an option shall be performed. D When approved by the purchaser, alloysSe, or XM1 may be furnished.

Free Technical Information

E When approved by the purchaser, alloy F may be furnished. B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc. Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed asfm accordance with Condition A, generally by the raw material manufacturer and adtm old worked to develop the specified properties.

Hex head, square head and hex socket cap screws.

Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed. AF – Headed and rolled from annealed stock and then reannealed AH – Asfm annealed and age hardened after forming.

ASTM F covers seven groups of stsinles steel alloys, including twelve austenitic, two ferritic, four martensitic and one precitipitain hardening. A Where options are given, all the tests under an option shall be performed.