the equipment requirements documented here, as experience shows that legal regulations are modified at irregular intervals. Last updated: late (ECE-R48 . STATUS OF UNITED NATIONS REGULATION ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THE. Regulation No. 48 establishes minimum requirements for lighting equipment towards ensuring satisfactory levels of traffic safety, including such areas as.
|Country:||United Arab Emirates|
|Published (Last):||20 May 2005|
|PDF File Size:||17.19 Mb|
|ePub File Size:||3.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
This tell-tale shall be non-flashing and shall not be required if the instrument panel lighting can ece r48 be turned on simultaneously with the front position lamps.
The Type Approval Authority shall strive to obtain a frequency of inspection of ece r48 per year. If ede above requirement is not practicable: The number of lamps mounted on the vehicle should be equal to the number s specified in each of paragraphs 6. No Contracting Party applying this Regulation shall refuse national ece r48 regional type approval of a vehicle type approved to the ece r48 series of amendments to this Regulation.
For side conspicuity markings see Annex 11, Figure 2 the observation plane is parallel to the longitudinal median plane of the vehicles situated ece r48 from the extreme outer ece r48 of the vehicle and bounded by: Other Requirements In the case where there is a positive indication in the communication form in Item This drawing represents a category M 1 vehicle, but the principle shown applies equally to vehicles of other categories.
They are consolidated, published in English, and updated on a regular basis. Rear ece r48 indicator lamps, rear position lamps, stop lamps ece r48 stop lamps of Category S4 and rear fog lamps with variable luminous intensity control are allowed, which respond simultaneously to at least one of the following external influences: In addition, the hazard warning signal may be switched on automatically to indicate to other road-users the risk of imminent danger as defined by Regulations; in this case, the signal shall remain switched “on” until it is manually or automatically switched “off”.
EUR-Lex Access to European Union law
The ece r48 and colorimetric requirements of a lamp shall be fulfilled when all other functions with which this lamp is grouped, combined or reciprocally incorporated are switched OFF. The angle of the light ece r48 from the dipped-beam headlamps must be determined under the following loading conditions.
However, the ecs authorities and manufacturers may jointly propose other methods either experimental or based upon calculationsespecially when the test poses particular problems, provided such ece r48 are clearly valid. Number Optional on ecd vehicles.
InterRegs: Regulation No. | ECE – United Nations
Treatment of vehicle in each loading condition The vehicle suspension and any other part likely to affect dipped-beam inclination shall be activated according to the methods described below. That point on the illuminating surface ece r48 is farthest from the vehicle’s median longitudinal plane shall not be more than mm from the extreme outer edge of the vehicle. The signal shall be operated by means of a separate control enabling all the direction-indicator lamps to flash in phase.
Appropriate evidence demonstrating compliance with the requirements indicated in Paragraph 5. On MMNNO and O vehicles mandatory amber side marker lamps may flash simultaneously with the direction-indicator lamps on the same side of the vehicle. Measurements The variation of the inclination of the dipped-beam shall be assessed for each of the ece r48 loading conditions in ece r48 to the measured initial inclination determined ece r48 accordance with Paragraph 5.
We do not re-word, summarise, cut or interpret the regulatory documents. The connection must ece r48 the parking lamp s on dce same side of the vehicle to be lit independently of any other lamps.
GAR | Installation of Lighting
If there is one, it shall not be possible to confuse it with the tell-tale for the front and rear position lamps. Number Two visible from the front and two visible from the rear. To verify compliance with a and b above, the oncoming and preceding power driven vehicle or vehicle-trailer combination ece r48 have position lamps if applicable and dipped-beam headlamps switched ON.
A light source module is so designed that regardless the ece r48 of tool sit ece r48 not mechanically interchangeable with any replaceable approved light source. Number According to the arrangement.
Other requirements The illuminating surface of the retro-reflector may have parts in common with the apparent surface of any other ece r48 situated at the front.
For the visibility of white light towards the rear, there must be no direct visibility of the ece r48 surface of a white lamp if viewed by an observer moving within Zone 2 in a transverse plane situated 25 m behind the vehicle see Annex 4 ; 5.
The states of loading to be used shall be as follows, as indicated in Annex 5 of this Regulation, for every system adjusted accordingly. On all vehicles the length of ece r48 exceeds 6 m, except for chassis-cabs; the length of trailers shall be calculated ece r48 the drawbar.
The vehicle shall be conditioned for ece r48 least 8 h at the temperature specified in paragraph 3. It shall be non-flashing.
ece r48 Contracting Parties applying this Regulation shall not refuse to grant extensions of approval ece r48 the preceding series of amendments to this Regulation. The parking lamp ecw and, if applicable, the front and rear position lamps according to Paragraph 6.
Orientation Ece r48 that the device illuminates the site of the registration plate. Transitional provisions ANNEXES Annex 1 Annex 2 — Communication — Arrangements of Approval Marks Annex 3 — Examples of lamp surfaces, rce and fce of reference, and angles of geometric visibility Annex 4 — Visibility of a red lamp to the front and visibility of a white lamp to the rear Annex 5 — States of loading f48 be taken into consideration in determining variations in the vertical orientation of the dipped-beam headlamps Ece r48 6 Ece r48 7 — Measurement of the variation of dipped-beam inclination as a function of load — Indication of the downward inclination of the dipped-beam headlamps cut-off referred to in Paragraph 6.
The daytime running lamp shall switch OFF automatically when the headlamps are switched ON, except when the latter are used to give intermittent luminous warnings at short intervals.
Front fog lamp 6. These ece r48 are determined in relation to the ece r48 of reference. Other requirements If one or more infrared radiation generator s is are installed inside the front position lamp, it they is are allowed to be activated only when the headlamp on the same side of the vehicle is switched on and the vehicle is in forward motion.
A fully searchable, accurate, user-friendly resource for consolidated regulations that are ece r48 quickly and ece r48. As from 48 months from the official date of entry into force of the 05 series of amendments, Contracting Parties applying this Regulation shall grant approvals only if the vehicle type to be approved meets the requirements of this Regulation as amended by the 05 series of amendments. Tell-tale indicating failure, as required by component regulation, fitted: