FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Daibei Vojin
Country: Luxembourg
Language: English (Spanish)
Genre: Video
Published (Last): 13 November 2013
Pages: 162
PDF File Size: 7.20 Mb
ePub File Size: 20.24 Mb
ISBN: 383-7-85308-342-8
Downloads: 32315
Price: Free* [*Free Regsitration Required]
Uploader: Samutaxe

The purpose of this manual is to give you a brief overview of the XL-2T control panel, and provide instructions for installing a basic system.

I then pressed code button followed by master proframthen user no 3 and then new 4 digit user code. The door of the metal cabinet may be removed to make it easier to install the control panel. The system features seven 7 fully programmable zones. I pressed the code button ready light did not flashthen pressed both 7 and 9 at same time, to reset master code to Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: On LED keypads the sounder will beep after each entry.

Enter the digit from the table below. Refer to the Installation Instructions for hookup information. The Extended Reporting Format: So now i activate the alarm on only a 3 digit code and it is working like that. The system must be in ready mode.

System Programming Programming Questions This topic defines the programming questions and the values for each question. There are 36 total questions, with multiple data entry locations.

To select a trigger type enter the 2 progrsm in either L1 L2 or L3 L4 desired trigger type for each output trigger. Section 5 – System Operations User Deletion User codes can be deleted directly through the keypad. Page of 93 Go. Section 5 – System Operations If a user code is not required to set the time, then enter: Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds.

TOP Related Articles  ASCENDENTES EN ASTROLOGIA EUGENIO CARUTTI PDF

For Built-in Siren Driver, connect a single 8 ohm speaker only. Table of Contents Xl2r to my manuals Add. Question 11, L1 – Exit Delay Fbbi this device some systems can obtain dial tone in areas which do not automatically provide dial tone.

FBI XL-2T Turbo Program Sheet

Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3. Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting. The system will report all signals to the primary receiver phone number. Question 32, L1 – Bypass Code Once deleted their values will be null. For Bell Output, connect a siren driver ex: Create an opening and mount a standard double-gang box. The following is a quick comparison.

We regret any inconvenience this may have caused and appreciate your continued support of FBII products. Some new features have been added and others have been modified. System ready to be armed System not ready to be armed The auto arm time represents the time of day that the area will automatically arm if it is not already armed.

TOP Related Articles  CREATIVE VISUALISATION SHAKTI GAWAIN FREE PDF

Trigger 1 must be selected for smoke detector power reset for this feature to active. After this time period, power is restored. This will be used by the CS downloading computer to determine the proper account information to download to this subscriber.

How can i change or get rid of this 3 digit code. For a period of 5 seconds the fire zone will not be scanned xl2tt the smoke detectors to settle. The FCC requires the following statement for your information. Next, enter the desired account number each digit followed by the key.

FBII XL-2T Installation And Setup Manual

Comments to this Manuals Your Name. Programming Questions This topic defines the programming questions and the values for each question. Page 81 – Extended 3×1 Ext. Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system. I want to change this 3 digit code to a new 4 digit code, but with no success. This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio prograk television reception.

The restore code will also be reported if the system is disarmed during an alarm. The keypads are surface mounted as described below.